INFORMATIVO: Motor ZC o d16a9 Ficha Tecnica


edgar

ej8 member
Mensajes
50
Puntos de reacción
0
ZC ENGINE

Timing Belt 88 Honda Prelude p/n - 14400-PK2-004
Distributor cap 88 Acura Interga p/n - 30102-PM7-305
Rotor 88 Acura Integra p/n - 30103-PM5-A05
Head Gasket 88 Honda Prelude p/n – 12251-PM7-003
Intake Gasket 88 Acura Integra p/n – 17105-PG6-S00
Exhaust Gasket 88 Acura Integra p/n – 18110-PG6-003
Water Pump 90 Honda CRX p/n – 19200-P01-004
Oil Filter 88 Acura Integra p/n – 15400-PR3-004
Clutch Parts 90 Honda CRX I used the CRX transmission and the CRX clutch
ZC Clutch disk use: 89 Honda Civic DX p/n - 22200-PM7-J02
ZC Pressure plate use: 89 Honda Civic DX

the 89 DX and the 89,90,91 CRX use the same size shaft and same number of splines on the transmission. The 89 DX clutch disk and pressure plate is smaller in diameter by about one inch than the CRX Si. Although the flywheel is the same diameter on both. As long as you stay with one or the other it should work fine.
Technical Data:
1.6L (1590 cc) DOHC
130-135 hp @ 6800 rpm
Bore 75.0
Stroke 90.0
C.R. 9.5:1 I can find no evidence of it being any higher than this.
91 octane. Some have reported no problems with 87, but the specified gas is 95 and/or 96 RON, which is equal to 91-92 'pump octane' available in the US.
Identification:
There are three versions of the ZC that I am aware of, but there could be more
D16A8 Euro. spec featuring EFI
D16A9 Euro. spec featuring Carbs
ZC Jap. spec featuring EFI
The ZC comes with a black valve cover with the cover bolts on the sides
The Honda symbol is on the exhaust side of the valve cover
The ZC comes with a 4-2-1 header style exhaust manifold
The ZC comes with a small oil to water oil cooler on the back of the block
The ZC has the same mounting points as the standard 88-91 CRX/CIVIC
Swap Info:
The ZC will bolt right in to the 88-91 CRX/CIVIC no fabricating or welding is needed
The swap can use your existing wiring harness if you have an SI, if you have a DX then minor modification is necessary. There is info on this procedure at the Honda Hybrid Page
You can use the SI or DX transmissions, they both bolt up. You can also use the SI or DX flywheel.
The engine only adds about twenty-five pounds to the front of the car, so your steering and suspension should be the same. If you are still concerned about the added weight, move your battery to your trunk.
Maintenance:
Spark plugs: NGK BCPR6E-11
Timing belt: Part no. 14400-PK2-004 (same as 88 Prelude)
Oil filter: Same as 88-89 Integra. Fram part no. PH3539A
Oil pan gasket: Same as 88-91 CRX/CIVIC or 86-89 Integra
Spark plug wires: Same as 86-89 Integra
Distributor cap and rotor: you can use the 88-91 CRX/CIVIC SI or 88-89 Integra
The exhaust manifold for Greddy Turbo kit for the 92-95 Civic, was originally designed for the ZC. Greddy modified the casting tool for the D16 ports, so there is plenty of material to safely port it back out to ZC sized ports. However, the guys at greddy say don't bother until you are running over 7 psi.
" The scoop on the headers, is that while the bolt pattern for the Civic SOHC engines and the ZC engines are identical, the port pattern is not. The ZC engine has the ports shifted almost 3 mm (appx 1/8"). In real terms, this means that when you use the SOHC header, the ports do not align properly. The exiting exhaust gases literally run into one edge of the misaligned header flange. You can see this by holding the steel exhaust gasket from the ZC engine up to the DC header.
The easiest and best solution is to use the ZC gasket as a template and mark the misalignment. Using an air grinder, with a small stone "port" the header to match the ZC port configuration. While you're at it clean up the entry point of the header a little so that the whole port on the header is slightly larger than the ZC port. It is an old, but proven trick that the larger header port decreases the chance of exhaust gas reversing flow and re-entering the still open exhaust valves. It is better to have the port larger than to have them matched identical. Do not under any circumstances grind the port on the head to match the header though. This gives poor results."
Tuning the ZC
Posted by Victor on November 25, 1997 at 21:53:23:
Just had my crx with a zc motor, dc headers, k&n, ultraflo, straight pipe, and stock ecu dyno. Baseline run came out to be 112.1hp, 98.6 ft-lbs @ 6800 rpm at the wheel. After installing cusco cam sprockets(v-tec), it increased to 118.8 hp, 107.0 ft-lbs at 6800 rpm at the wheel. This gain was not as significant as the power gain at 3000 rpm to 5000 rpm which was a gain of 16.2 hp and 26.9 ft-lbs. All runs were made on 3rd gear on a stock si tran. Like to thank Aries at dynamic autosports for his bomb-ass hypertuning adjustments!


3G ZC Swap
You need an 87 Integra parts to run an 87 F.I. ZC motor:

If you can get a Japanese ZC ECU get it!! I had it, it runs good at
idle. The 86-87 ECU tends to run a little rich at idle (stinky fumes
emmitted), the ZC ECU fixes that
& runs a bit smoother (way less fumes).
-Katman
d16a1 = 1st gen 'teg
d16a8 = euro w/o cat
d16a9 = euro with cat zc = japan (jdm)
89 Integra valve seals DO FIT a ZC Message by Rocky on November 04, 1998 at 10:41:28
There was some discussion in this forum about the valve seals that are used by a ZC. It was said not use 89 Teg valve seals, I wanted everybody to see the results of my findings, so that they don't take their head apart because they thought that they installed the wrong ones. This is not a flame on anybbody, I just want to post this info.
I did some research into it, after an initial scare. I asked an Acura tech and he told me that almost all Integras have the same size valve stems dia. approx 6.6mm. My Helm book for 89 Integra confirms this, it says 6.56mm-6.52mm. My other Helm book for the 91 Civic says that the SOHC engines have 5.46mm-5.42mm valve stems.
I removed my exhaust manifold (again) and stuck a pair of dividers in the port to get a measurement. I did not use the most exact method because my dividers had straight legs instead of the ones where the tips curve in (wouldn't fit in the port). I then measured them with my calipers and got 6.5mm! I would say that that is pretty close.
I also got to thinking, if it was thought that the Teg had the 5.5mm valves, somebody would have noticed that when the valve seals were being installed. I'm sure that the machine shop would have given me a call to let me know that I got the wrong seals, that is quite a bit of slop for a "seal". So after all this, the 89 Teg valve seals DO fit a ZC.


From: Anthony RoddickMy car is an originalfactory equipped 1988 ZC Civic hatch Si with the bulge in the bonnet.engine zc 1590ccidle 730rpm manual 700rpm autostatic timing 16 deg BTDC manual and autocompression measure at 250rpm and wot----nominal 192psi(1,324kPa, 13.5kgcm2) minimum135psi(932kPa, 9.5kgcm2) maximum variation28psi(196kPa, 2kgcm2)cylinder head warpage limit 0.05mm(0.002") height 131.95-132.05mmvalve clearances inlet 0.13-0.17mm(0.005"-0.007") exhaust 0.15-0.19mm(0.006"-0.008")stem to guide clearance in 0.02-0.05mm(0.001"-0.002") limit0.08mm(0.003") ex 0.05-0.08mm(0.002"-0.003") limit0.12mm(0.005")valve seat width ex&in 1.25mm-1.55mm(0.049"-0.061") limit 2.0mm(0.08")fuel - 96+ octane unleadedParts Interchange List

Engine Mounts:-----1988-91 CRX/Civic

Timing Belt:-----1988 Prelude 2.0
AC Compressor / Parts:-----1989-91 CRX/Civic
Throttle Body:-----1988-91 CRX/Civic
TPS:-----1988-91 CRX/Civic
ECU:-----1989-91 CRX/Civic Si, 88-89 Integra 5-spd, 89-91 ZC
Intake:-----1988-91 CRX/Civic
Headers/Exhaust Manifold-----88-91 CRX can be used port will not be perfect---Ideal is DC 86-89 Integra Top with 88-91 CRX downpipe---(I use port matched GUDE 4-1 Header)
Plug Wires:-----1986-89 Integra
Spark plugs:-----1986-89 Integra or 1988-91 CRX/Civic----- NGK BCPR6E-11
Distributor Cap:-----1988-91 CRX/Civic 1988 Integra
Distributor Rotor:-----1988-91 CRX/Civic 1988 Integra
Head Gasket:-----1988 Prelude
Intake Gasket:-----1988 Integra
Exhaust Gasket:-----1988 Integra
Water Pump:-----1989-91 CRX
Oil Filter:-----1988-89 Integra-----Fram PH3539A
Oil Pan Gasket:-----1988-91 CRX/Civic or 1986-89 Integra
Flywheel from 1989-91 CRX Si may be used
Transmissions:
4 speed 88-91
5 speed DX 88-91
5 speed Si 88-91
5 speed ZC 88-91
ZC Pressure Plate:-----1989 Civic DX
ZC Clutch Disk:-----1989 Civic DX
I know these have been asked before, and I know they will be asked again,
but here are a few ZC tranny questions.

1.) For axles, I use the ZC halfshafts, 90-93 teg axles, and the 90-93
axles fit on all the 4G hubs?
2.) Which clutch, preassure plate, and flywheel do I need? 90-91?
3.) Does Quaife make a limited slip that would fit the ZC tranny? Are
the diffs in the ZC the same as in the other 4G's?
Thanks,
Craig
1) A better choice of axle would be two 88-91 Civic/CRX DX/Si right
hand axles with 90-93 Integra inner joints. If you have a CRX HF or
Civic Standard model a custom job is called for. OR you can use 88-91 DX\Si knuckles and hubs and make your life simpler.

2) The clutch should match the year of the transmission you have, 88
if it is an 88 and your choice of 89 or 90-91 if the transmission is
89 or later.

3) Yes they do, I have one, it is not available through Autotech
though.
If the tranny is an 89 or later you may use a 90 91 clutch, pressure
plate and flywheel.
brian g

I'm wondering whether it is worth it to pay extra for the ZC Tranny, with the Integ axles, rather than the Si tranny?
ZC: Si:
1st: 3.250........ 3.250
2nd: 1.944........ 1.894
3rd: 1.346........ 1.259
4th: 1.033........ .937
5th: .878........ .771
final 3.888........ 4.250

ZC.jpg
 


alguien se anima a traducir esto? :D
 


Voy :) ......

Faja de Tiempo - 88 Honda Prelude P/N - 14400-PK2-004
Tapa del distribuidor - Acura Interga 88 P/N - 30102-PM7-305
Rotor - Acura Integra 88 P/N - 30103-PM5-A05
Empaque de Valvulas - Honda Prelude 88 P/N - 12251-PM7-003
Empaque de Admision - Acura Integra 88 P/N - 17105-PG6-S00
Empaque de Multiple de Escape - Acura Integra 88 P/N - 18110-PG6-003
Bomba de Agua - Honda CRX 90 P/N - 19200-P01-004
Filtro de Aceite - Acura Integra 88 P/N - 15400-PR3-004
Piezas de Clutch - Honda CRX 90
Disco de Clutch - 89 Honda Civic DX P/N - 22200-PM7-J02
Canasta - 89 Honda Civic DX

El 89 DX y los 89-90-91 CRX usan el mismo tamaño del árbol y el mismo número de estrías en la transmisión.

El disco de embrague y la canasta del 89 DX es menor en diámetro, aproximadamente una pulgada de la del CRX Si. Aunque el volante es el mismo diámetro en ambos.

Datos técnicos:
1.6L (1590 cc) DOHC
130-135 hp @ 6,800 rpm
Bore 75,0
Stroke 90,0
Compression Ratio 9.5:1

Identificación:

Hay tres versiones de la ZC que yo sepa, pero podría haber más
D16A8 euros. con especificación de EFI
D16A9 euros. con las especificaciones Carburadas
ZC Japonés. con especificación de EFI

El ZC negro viene con una tapa de válvulas con la cobertura de pernos a los lados
el símbolo Honda esta en el lado del escape de la tapa de válvulas
El ZC viene con un múltiple de escape 4-2-1
El ZC viene con un pequeño enfriador de aceite en la parte trasera del blok
El ZC tiene los cargadores en los mismos puntos que el 88-91 CRX / CIVIC estandar

Información para Swap:

El ZC caza perfectamente en un 88-91 CRX / CIVIC no hay necesidad de modificar o soldar nada.
El SWAP puede aprovechar su actual cableado si tiene un SI, si tiene DX entonces es necesario una pequeña modificación. No hay información sobre este procedimiento en la página de Honda Híbrid.

Puede utilizar transmisiones SI o DX, ambos cazan perfectamente. También puede utilizar el volante de SI o DX.

El motor sólo añade unas veinticinco libras a la parte delantera del auto, de modo que su dirección y la suspensión puede ser el mismo. Si se preocupa por el peso añadido en la parte frontal del auto, se sugiere mover la batería al baul.

Mantenimiento:

Bujías: NGK BCPR6E-11
Faja de Tiempo: parte no. 14400-PK2-004 (igual a 88 Prelude)
Filtro de aceite: Igual que Integra 88-89. parte no. PH3539A
Oil pan gasket: Igual que el CRX 88-91 / 86-89 CIVIC o Integra
Cable de bujía: Igual que Integra 86-89
Tapa de distribuidor y el rotor: se puede utilizar el CRX 88-91 / 88-89 CIVIC SI o Integra

El multiple de escape de un Turbo Kit Greddy para el CIVIC 92-95, fue diseñado originalmente para la ZC.
Greddy modificó la herramienta para la fundición D16 puertos, así que hay un montón de material de seguridad para volver a puerto a los puertos de tamaño ZC. Sin embargo, los chicos en Greddy dicen que no se moleste hasta que se están a más de 7 psi.

Mientras el patrón de los pernos de los motores CIVIC SOHC es idéntico al del ZC, el patrón del puerto no lo es. El motor ZC tiene de diferencia casi 3 mm en los puertos (Aproximadamente 1 / 8"). En términos reales, significa que cuando se utiliza los headers de un motor SOHC, los puertos no se alinean correctamente.
La salida de los gases de escape, literalmente, corren al borde del flange de los headers.
Usted puede ver esta comparación, sosteniendo el escape del motor ZC hasta el header DC.

La forma más fácil y mejor de solucionar esto es utilizar empaque de escape del ZC como plantilla y marque la desalineación. Use un esmeril de aire, con una pequeña piedra, y portee los headers para que coincidan con la configuración de puerto ZC. Cuando lo hagan, la limpieza del punto de entrada de la cabecera es importante y verán que todo el puerto en el encabezado es ligeramente más grande que el puerto ZC

Es un viejo truco, pero demostrado, que el puerto mas grande del escape, disminuye la posibilidad de invertir el flujo de gases de escape y vuelva a entrar en las válvulas de escape todavía abiertas. Es mejor tener el puerto más grande que tenerlos idénticos. Por ningún motivo moler el puerto en la culata, para hacerlo coincidir con los headers. Esto da pobres resultados.

Tuneando el ZC:

Publicado por Víctor el 25 de noviembre de 1997 a las 21:53:23:

Acabo de obtener mi CRX con motor ZC, headers DC, k & n, ultraflo, tubo recto, y ECU stok. La Linea del dyno llegó a ser 112.1hp, el 98,6 libras-pie @ 6800 rpm a las ruedas.
Después de instalar cusco Sprokets(v-tec), aumentó a 118,8 HP, 107.0 pies-lbs a 6,800 rpm a las ruedas. Este aumento no fue tan importante, como el poder ganar en 3000 rpm y 5000 rpm que es una ganancia de 16,2 CV y 26,9 pies-lbs. Todas las pruebas fueron en Tercera velocidad en una caja si s. Quiero dar las gracias al dinámico Aries autosports por su bomb-ass hypertuning ajustes!

3G ZC Swap
Usted necesita partes de un 87 Integra para hacer funcionar un 87 F.I. ZC motor

Si usted puede conseguir un ECU japonés ZC consigualo!, se ejecuta bien en vacio. El ECU 86-87 tiende a correr un poco rica en vacio (emite humo apestoso), la ECU ZC arregla eso y corre un poco más suave (forma menos humo).

d16a1 = 1 ª generación TEG
d16a8 = euro w/o cat
d16a9 = euro with cat zc = Japón (JDM)

Los sellos de válvulas del Integra 89 quedan en un ZC Mensaje por ZC Rocky el día 04 Noviembre, 1998 en 10:41:28
Hubo cierto debate en este foro acerca de los sellos de válvulas que se utilizan por un ZC. Se dijo que no se utilizará sellos de válvulas de TEG 89, Yo que quería todos vieran los resultados de mis conclusiones, por lo que no tienen su cabeza aparte porque pensaban que instalar el mal queridos. e pregunté Acura Tech y me dijeron que casi todos los Integras tienen el mismo tamaño de la valvula en diámetro. 6.6mm aprox.
Mi libro Helm de Integra 89 lo confirma, dice 6.56mm-6.52mm.
Mi otro libro Helm para los Cívic 91 dice que los motores SOHC tienen 5.46mm-5.42mm.

Quité mi escape de nuevo y se clavó un par de separadores en el puerto para obtener una medición. No utilizar el método más exacto (que no caben en el puerto). Luego mide con calibradores y obtuvo mi 6.5mm! Yo diría que es bastante estrecha.
Yo también llegué a pensar, si se pensaba que el Teg tuvo la válvulas de 5,5 mm, alguien habría notado que la válvula selle cuando se esté instalando. Estoy seguro de que la tienda me hubiera dado una llamada, que me haga saber que compre mal los sellos, que es un poco de vertiente para un sello. Así que después de esto, los sellos de válvulas del Teg 89 encajan en un ZC
 

Última edición:


Atrás
Arriba